OrynosMusic
Temporary Free phase · 5,000 weekly credits after verification

All modules and models are included for verified accounts. Each render uses the displayed model credit cost. Purchased credits remain in your account; new purchases are paused.

Sign in and verify your email to activate Free access. Sign in · Create account

OrynosMusic / Mixing studio

Mixing

Bring your beat and vocals together. Choose a model, check the stem roles and let the mix adapt to your audio.

Processed in RAM. Five minutes of focused tab time to download, with a one-hour limit after completion.

Drop your multitracks here

Sign in and verify your email for full access to Mixing and all models.

Export stems without a limiter, with natural headroom and a matching sample rate.

Check your stems.

Choose the role for each file. Use the arrow for level, pan, tuning and manual processing.

0Stems
-Longest file
-Sample rate
-Upload size
Orynos AI · distinct DSP models

Choose your model.

Access & credits ↗

Galaxy · Recommended for mixing. Its dedicated stem processing makes room for vocals and separates kick and bass before the final master.

Loading model access…

Analysis depth

One final master. Higher depths use more source measurements and finer output checks; the multiplier describes analysis budget, not a sound-quality score.

Frame-by-frame narrow resonance control; correction capped at 3.5 dB, with onset protection.

Uses spectral onset motion to retain attacks during resonance control.

Reduces opposed stereo energy only in affected frequency/time cells.

Mix only: measures the buses after faders and creates space for active vocals. Model-dependent cuts stay within 4 dB.

Mix only: labelled drum energy ducks the low band of bass stems.

Deshimmer-derived narrow high-frequency artifact suppression. Protects transients and broad musical events. Audition: musical tones can also trigger it.

DSP source ↗

Independent bass, mid and high-band gain control.

Reduce low-frequency side energy below 110 Hz.

Measure the mix and apply bounded five-band tonal correction.

Gentle broadband gain control keeps both channels linked.

Oversampled nonlinear coloration and extra low-frequency body.

Finishing collection · 7 optional tools

Adaptive control of moving sub-bass.

A gentle lift to attack with less sustain.

Soften the upper spectrum with a restrained high-band blend.

Remove energy below 30 Hz before model processing.

Smooth the final 50 ms to reduce end clicks.

Reduce side energy when channels have negative correlation.

Level-dependent attenuation of harsh upper-band peaks.

Create a custom profile Included
Discord collection Members

Connect Discord in Settings to unlock three exclusive recipes and a loudness-matched listening pack.

Connection settings ↗

Choose a model to see its processing path and controls.

All modules and models are included for verified accounts during the temporary Free phase. Access & credits

Shape the balance.

Balanced is a neutral starting point. Leave vocal balance at zero to use the measured level.

Automatic source processing
Behind the beatMore forward

An optional level trim after automatic balancing. Space control targets overlapping vocal frequencies instead of turning down the whole beat.

Reverb and delay start off. Add space in Mix details when your song needs it.

Mix detailsBalance, effects, buses & export

Fine-tune your mix.

Optional controls. Your changes are kept when you move between steps.

No local settings snapshot

Balance

Set the main balance controls.

Sets how far forward the measured vocal target sits before your vocal balance trim.
Section automation is included after email verification.
Available when section automation is included in your plan.
Controls low-end cleanup and kick-to-bass separation.
Expands selected buses while protecting the low end.
Balances punch against smoothness on drums and music.
Maximum cut in overlapping vocal frequencies. Zero disables this control; the full beat is not volume-ducked.
Reduces masking in the sub region when kick energy hits.
Adds controlled cohesion before final safety limiting.
Recommended for sending the mix into the Mastering Engine.

Effects

Reverb, delay and vocal ducking.

Reverb

Ping-pong delay

Vocal FX ducking

Reference matching (Premium)

No reference loaded

Buses

Adjust the five internal mix groups.

Export

Choose the output format.

Verify your email to activate output up to 192 kHz.

Your mix is ready

Rendered from the current routing and settings.

0:000:00
-Sample rate
24-bitBit depth
-Output peak
-Output RMS
-Section automation
-Vocal anchor
CleanMix direction
V6.1Engine

How to mix vocals and a beat

Vocal mixing guide ↗
  1. Upload aligned WAV stems.

    Export every stem from the same start point. Keep the same sample rate and leave space before clipping.

  2. Check roles and balance.

    Assign your beat, lead vocal and doubles. Choose a model and direction, then use the optional controls when the measured balance needs an adjustment.

  3. Render and listen.

    Download the WAV mix and check the whole song, including words, transients and effect tails. Keep your stems so you can revise the balance.

Can I mix vocal doubles?

Choose Double, Doubles L or Doubles R for supporting vocals. A general mono double can be given a stereo treatment; separate left and right recordings can use their own roles. Keep the main performance assigned as the lead.

How do I keep a finished beat from being overprocessed?

Start with Balanced and vocal balance at zero. Check the automatic processing, then use manual stem controls or lower the optional interaction amounts where needed. A beat that is already limited needs different treatment from raw instruments.

Is mixing the same as mastering?

Mixing balances separate stems. Mastering processes the finished stereo mix. If your balance is already right, use online mastering. Finished mixes have five minutes of focused result-tab time to download, with a one-hour RAM limit after completion.

Done
Confirm your email address to receive subscription and account notices.